issue no. : pc-04-006 date of issue : march 2, 2004 classification : new messrs. digi-key delivery specification product description : balun product part number : EHF4BE5250 a pplications : cellular phone for other applications, contact the undersigned in advance. term of validity : five years from the date of issue. receipt used column matsushita electronic components co., ltd. module device company module business unit 992-1 aiba ohno-cho ib i-gun gihu pref 501-0598 japan tel +81-585-36-2345 fax +81-585-36-2353 communication module business group prepared by : h. ito authorized by : m. mizuno [manufacturing section] (name) matsushita electronic components co., ltd. (address) 992-1 aiba ohno- cho ibi-gun gihu pref 501-0598 japan the same as above final production plant final inspection plant
balun delivery specification enact. date march 2, 2004 enfo. date march 2, 2004 p.s.m ----- approval m. mizuno check m. mizuno plan h. ito EHF4BE5250 appearance drawing no. 151-ehf-4be5250 9-1 [shape, appearance, dimension] unit: mm ceramic substrate sn ni a g-pd item appearance/ construction marking remarks description product surface shall be covered with a protective film, which does not easily separate nor present noticeable unevenness, scratches, pinholes, color changes etc. terminals shall ensure practically acceptable quality substrate shall be as shown in the drawing with no excessive chippings, scratches, burrs, or cracks. shall be legible in black (with printing paste) marked side for pin 1 weight of the individual component: 3mg note 1) ?typ? is used where no dimensional tolerance applies. 0.65 + / - 0 . 1 nu (6) (1) in out2 (4) (3) out1 ( 4 ) 1.6+ / -0.1 0.8+/-0.1 ( 6 ) ( 1 ) ( 3 ) gnd (5) (2) gnd ( 5 ) ( 2 )
balun delivery specification enact. date march 2, 2004 enfo. date march 2, 2004 p.s.m ----- approval m. mizuno check m. mizuno plan h. ito EHF4BE5250 specification and measurement drawing no. 151-ehf-4be5250 9-2 unit mhz db ohm ohm - db deg typ. - - 50 100 - - 180 max. 5350 1.2 - - 2.0 1.5 195 [absolute maximum ratings] no. 1 2 3 item maximum input power operating temperature storage temperature symbol pmax topr tstg rating 100 -30?+85 -40?+85 unit mw degc degc remarks dc bias must be 0v note: this component cannot apply a dc bias. [electrical characteristics] t=-30?+85degc no. 1 2 3 4 5 6 7 item frequency insertion loss (back to back) unbalance impedance balance impedance unbalance port vswr a mplitude balance phase balance test circuit - fig-2 - - fig-1 fig-1 fig-1 min. 5150 - - - - -1.5 165 [ internal circuitry ] ( 4 ) out2 ( 3 ) out1 ( 1 ) in ( 2 ) gnd (2)gnd [ measuring circuit ] fig.1 gnd gnd gnd b a c gnd gnd e d network analyzer s-parameter test set in out < phase balance measurement > ? phase1 a=in, b=out, c=terminal resistor (50 ohm) ? phase2 a=in, c=out, b=terminal resistor (50 ohm) ?phase balance phase balance=phase1-phase2 < insertion loss measurement > assuming the loss as ?loss? when d=in, e=out insertion loss for a device is ?loss?/2 s p ecification fig.2 (5)gnd
(3) bottom view (4) (1) (6) (2) (5) balun delivery specification enact. date march 2, 2004 enfo. date march 2, 2004 p.s.m ----- approval m. mizuno check m. mizuno plan h. ito EHF4BE5250 terminals/recommended lands drawing no. 151-ehf-4be5250 9-3 [recommended pcb pad dimensions] unit: mm [terminal dimensions] unit: mm 0.2 + / -0.1 0.3 1.4 0.55 pcb pad 0.55 + / - 0 . 1 0.25 + / - 0 . 1 0.3 + / - 0 . 1 0.4 + / -0.1 0.2 + / -0.1 0.3 0.55 0.30 pin no. product 1.45 0.25 0.55 + / - 0 . 1 (1) in top view (6) nu (3) out1 (4) out2 (2) gnd (5) gnd 0.3 0.3
balun delivery specification enact. date march 2, 2004 enfo. date march 2, 2004 p.s.m ----- approval m. mizuno check m. mizuno plan h. ito EHF4BE5250 quality characteristics drawing no. 151-ehf-4be5250 9-4 fr-4 ( t=1.0mm ) , 45+ / -2mm span, 5+ / -1sec. 1mm step, 2mm judgment criteria no abnormality shall be observed in appearance or electrical characteristics over 95% of the terminal surface shall be covered with solder there should not be any cracks in the component or solder j oints, no abnormality in electrical characteristics. test condition -40?+85degc, each 30 min., 200cy +85degc, 1000h +85degc, 85%rh, 1000h -40degc, 1000h 0.35mm 10-55hz, 50m/s 2 55-500hz 10-500-10hz/11min.,in each direction of xyz, 2h 1.8m, 6 facesx3cy(with 100g dummy load) reflow: 260degc peak, 3 times 200pf, 0 ohm, +/-200v, each 3 times solder bath: 230+/-3degc, 3 sec. test item temperature cycling high temperature high-temperature high-humidity storage low temperature vibration shock (drop) soldering heat resistance electro static discharge solder ability board warping terminal removal seating plane co-planarity [ quality characteristics ] < recommended soldering condition > diagram1 shown below is a recommended reflow soldering condition degc 260 230 200 175 150 135 tem p erature 60~120 sec. time 60~70 sec. 2mm 45mm t=1.0mm 45mm within 0.1mm solder a component on a pc board using the recommended condition shown below and then press the component sidewa y s at 1mm/sec. destruction limit 4.9n or g reater.
balun delivery specification enact. date march 2, 2004 enfo. date march 2, 2004 p.s.m ----- approval m. mizuno check m. mizuno plan h. ito EHF4BE5250 cautions drawing no. 151-ehf-4be5250 9-5 [ cautions for use ] (1) operating a product over the maximum rating for even a moment may result in a product failure or breakage. never use a pr oduct in such a condition that it may cause a safety problem. (2) opening or short-circuiting the product terminals or inserting a product in the reverse orientation while power is being supplied may cause a breakage. always avoid such circumstances. (3) operations in a corrosive gas atmosphere or improper environments such as high- temperature, high-humidity or dewy conditions may lead to product performance deterioration, a breakage, a change in appearance etc. please avoid such conditions, as they are unsafe. (4) always ground the soldering iron or soldering bath used for assembly operation to avoid any excessive voltage applied to a product. (5) after soldering with solder bridges, incomplete soldering or in the reverse orientation, supplying power may result in a product breakage. please confirm the soldered condition before s upplying power to the product. (6) excessive stress on the terminals may cause a contact failure or performance deterioration. please use caution. (7) please provide a fail-safe provision in the product you design by taking any failure of our product into consideration. (8) this product does not include a dc-cutti ng device. application of a dc voltage between the balance port and the unbalanc e port may cause product deterioration or breakage. * if any question arises about the safety of this product, please contact us immediately with a request for an engineering examination. [remarks] *1: all of the materials used in this produc t are those listed as the existing chemical substances based on the ?law for examination and regulation of manufacture of chemical substances? *2: the production process of this pr oduct does not use any ozone-depleting chemicals (ozc) regulated by the montreal protocol. *3: validity of this specification is 5 years from the date of issue, but the validity is considered on going unless any changes are made.
balun delivery specification enact. date march 2, 2004 enfo. date march 2, 2004 p.s.m ----- approval m. mizuno check m. mizuno plan h. ito EHF4BE5250 packaging specification 1 drawing no. 151-ehf-4be5250 9-6 [ packaging materials ] 1. materials 1) embossed carrier tape (refer to the attachment) 2) top tape: anti-static 3) packaging box (refer to the attachment) 4) packaging tape, carrier-securing adhesive tape 2. specification no. 1 2 3 4 5 6 7 8 9 10 item reel outer diameter reel inner diameter reel inner width quantity in a reel taping direction top tape attachment position label attachment position tape leader part and tape ending part missing products packaged quantity in a box remarks tape breaks force. min. 10n top cover tape strength. min. 10n tape peel force. 0.1?1.0n tape peel angle. 165?180degree reel weight. max 1500g indicated item pat no., lot no. quantity, maker country 84000 pieces/box(max) condition refer to the attachment refer to the attachment refer to the attachment 4000 pieces/reel tape unreeling direction (with markings facing up) top tape < top tape attachment area > embossed tape top tape edge must stay inside the sprocket holes of the embossed carrier (sprocket holes shall not be covered) tape unreeling direction label leader part no missing products shall be allowed 21 reels/box (max) 8.0+/-0.2mm 5.5mm 200~220mm (product-unloaded part) 100~150mm, 25~38 pieces worth, (product-unloaded part) 300~ 400mm ending part product-loaded part top tape embossed carrier
balun delivery specification enact. date march 2, 2004 enfo. date march 2, 2004 p.s.m ----- approval m. mizuno check m. mizuno plan h. ito EHF4BE5250 packaging specification 2 drawing no. 151-ehf-4be5250 9-7 1. method 1) load products in each cavity of an embossed carrier tape, in the correct orientation, by leaving the product-unloaded part shown in item no. 8(p9-6) of the packaging specification. 2) heat-seal a top tape in good alignment on the carrier tape. 3) after 4000 pieces are loaded and reeled, pr ovide a product-unloaded part at the tape-leade r portion. secure the tip of the carrier tape with a piece of adhesive tape. 4) stack the reels (21 reels max.) and enclose th em in a packaging box. close the flaps with a piece of adhesive tape. 5) provide markings on the packaging box. < items to be indicated > 1. part no. 2. quantity 3. lot no. 4. manufacturer name 5. country of origin * insert cushion material in the empty spaces to secure reels number of stacking, 21 reels max. packaging box shape varies with the number of reels enclosed reel label marking on the packaging box
balun delivery specification enact. date march 2, 2004 enfo. date march 2, 2004 p.s.m ----- approval m. mizuno check m. mizuno plan h. ito EHF4BE5250 packaging specification 3 drawing no. 151-ehf-4be5250 9-8 [embossed tape dimensions] unit: mm (1) unspecified corner radius shall be 0.3mm max. (2) cumulative pitch error of sprocket holes shall be +/-0.2mm for 10 pitches. 0.25 + / -0.05 0.7 + / -0.1 4 + / - 0 . 1 2 + / - 0 . 0 5 2.0 + / -0.05 d1.5 1.75 + / - 0 . 1 1.0 + / -0.1 0.3 5deg max +0.1 -0 4.0 + / - 0 . 1 r0.3 max r0.3 max 3.5 + / - 0 . 0 5 (2.75) 8.0 + / - 0 . 2 1.8 + / - 0 . 1 5deg max
balun delivery specification enact. date march 2, 2004 enfo. date march 2, 2004 p.s.m ----- approval m. mizuno check m. mizuno plan h. ito EHF4BE5250 packaging specification 4 drawing no. 151-ehf-4be5250 9-9 [reel dimensions] unit: mm (1) this reel conforms to eiaj-rrm-08b based on eiaj standard (2) material: ps (polystyrene) number ? 4 4 ? 4 4 ? 3 r 8 5 a ? 1 8 0 0 - 3 h n ? 60 +1 0 ? 13 b 3b 3b w1 w2 h 3 5 4 110 105 0.8 0.6 0.4 0.2 0.8 0.6 0.4 0.2 scale ? 3 2 min 18.0 3 } 0.2 2 m i n 1 8 . 0 2 m i n 1 8 . 0 2 } 0.2 r 1 0 . 5 } 0 . 4 ? 1 0 1 2 0 ? } 0 . 2 1 2 0 ? } 0 . 2 r 0 . 5 2 - r 1 2 - r 1 rim , hub rim a hub n 180 0 -3 60 +1 0 inner width , outer width tape width inner width w1 outer width w2 8 9+/-0.3 11+/-1.0 center area label 105...50
|
